[AJC]

Does anyone know what the Camaro's dimensions are? Width & length

 

[brandonppr]

Welcome:hello:

Are you looking for the Concept or production dimensions?
The production dimensions are not out yet.
I don't know the dimensions of the concept but I am sure someone will chime in.

 

[brandonppr]

http://www.5thgen.org/forum/showthread.php?t=270&

At 110.5 inches, the concept's wheelbase is not only longer than the 1969's (by 2.5 inches), but also longer than the new Mustang's by 3.4 inches. The team wanted to lower the concept's visual stance, and the extra wheelbase helped, but not as much as the almost 6 inches of track added up front (3 inches were added at the rear). At 63.8 inches front/63.3 rear, the concept is only slightly wider than the current Mustang, but its dimensions may change on the way toward production.

 

[AJC]

I am trying to get the length & width to see if it will fit in my garage.

 

[Luwinkle]

Rent a mustang and park it in there. If it fits with room to spare, you'll probably be good.

 

[OctaneZ28]

What kind of car is in the garage now?
We can compare it to that.

Keep in mind all we know right now are the dimensions of the concept car.
Production car dimensions have yet to be revealed.

 

[AJC]

I had a 2007 Mustang GT and it fit but not much room to spare.

 

[OctaneZ28]

Compared to the 2005-08 Mustang, Camaro will be very similar in dimensions...
about 1 inch longer, about 2 inches wider, and about 1 inch shorter.

 

[CUONCRS]

Compared to the 2005-08 Mustang, Camaro will be very similar in dimensions...
about 1 inch longer, about 2 inches wider, and about 1 inch shorter.

And don't forget, about 150 feet further ahead.... :rotflmao:

 

[AJC]

I found these dimensions and I hope the width is not 79.6 in because I will have a hard time getting it in my garage. I think 79.6 in for the width is way to wide.


SPECIFICATIONS

Dimensions
Exterior length: 186.2 in.
height: 53.0 in.
width: 79.6 in.
wheel base: 110.5 in.

Interior maximum seating: 4

 

[89RS]

I remember reading in the Edmunds forums a while back about the Camaro's specs. GM was quoted as saying that the production model would be 3/4" taller and a 1/2" narrower than the concept.

 

[$¢'s 5th Gen]

And don't forget, about 150 feet further ahead.... :rotflmao:

You must have let him get the jump on you:lol:

 

[CUONCRS]

You must have let him get the jump on you:lol:

:rotflmao:

 

[OctaneZ28]

I found these dimensions and I hope the width is not 79.6 in because I will have a hard time getting it in my garage. I think 79.6 in for the width is way to wide.


SPECIFICATIONS

Dimensions
Exterior length: 186.2 in.
height: 53.0 in.
width: 79.6 in.
wheel base: 110.5 in.

Interior maximum seating: 4

From what I've heard, the 79.6 is actually an error, and it should read 77.6.
Production car will be around 76 inches in width I'm guessing.

 

[CUONCRS]

I found these dimensions and I hope the width is not 79.6 in because I will have a hard time getting it in my garage. I think 79.6 in for the width is way to wide.

If it were me, I'd be looking for a new garage that my Camaro would fit in. :lol:

 

[AJC]

If it were me, I'd be looking for a new garage that my Camaro would fit in. :lol:

I'll make it fit.