[CamaroPA]

BRAKES
Brake Pipe Fitting 16 N.m 12 lb ft
Brake Pipe Fitting - Master Cylinder 23 N.m 17 lb ft
Brake Pressure Modulator Valve (BPMV) Nut 8 N.m 71 lb in
Electronic Brake Control Module (EBCM) Bolt 3 N.m 27 lb in
Wheel Speed Sensor Bolt 9 N.m 80 lb in
Yaw Sensor Nut 9 N.m 80 lb in

INTERIOR FASTENER TIGHTENING SPECIFICATIONS
Front Floor Console Fastener 2.5 N.m 22 lb in
Front Floor Console Rear Cover Fasteners 2.5 N.m 22 lb in
Instrument Panel Assembly Fasteners 2.5 N.m 22 lb in
Instrument Panel Carrier Support Bracket Fasteners 2.5 N.m 22 lb in
Instrument Panel Compartment Door Dampener Fasteners 2.5 N.m 22 lb in
Instrument Panel Compartment Door Fasteners 2.5 N.m 22 lb in
Instrument Panel Compartment Door Latch Fasteners 2.5 N.m 22 lb in
Instrument Panel Driver Knee Bolster Energy Absorber Fastener 2.5 N.m 22 lb in
Instrument Panel Inflatable Restraint Fasteners 22 N.m 16 lb ft
Instrument Panel Tie Bar Assembly to the Vehicle Body 25 N.m 18 lb ft
Instrument Panel Tie Bar Assembly to the Vehicle Cowl 9 N.m 80 lb in
Instrument Panel Tie Bar Assembly to the Windshield
Frame and Plenum Panel 22 N.m 16 lb ft
Instrument Panel Trim Pad Fasteners 2.5 N.m 22 lb in
Instrument Panel Trim Plate Retainer Fastener 2.5 N.m 22 lb in
Instrument Tie Bar Assembly to the HVAC Module Assembly 9 N.m 80 lb in
Roof Console Fasteners 2.5 N.m 22 lb in

BRAKES
Brake Caliper Bleeder Valve 10 N.m 89 lb in
Brake Caliper Bolt - Front (L99, LS3) 60 N.m + 90 degrees 44 lb ft + 90 degrees
Brake Caliper Bolt - Rear (L99, LS3) 40 N.m + 90 degrees 30 lb ft + 90 degrees
Brake Caliper Bracket Bolt - Front (LLT) 40 N.m + 90 degrees 30 lb ft + 90 degrees
Brake Caliper Bracket Bolt - Rear (LLT) 40 N.m + 90 degrees 30 lb ft + 90 degrees
Brake Caliper Guide Pin Bolt - Front (LLT) 27 N.m 20 lb ft
Brake Caliper Guide Pin Bolt - Rear (LLT) 27 N.m 20 lb ft
Brake Hose Fitting Bolt 40 N.m 30 lb ft
Brake Rotor Bolt 10 N.m 89 lb in
Brake Shield Bolt 9 N.m 80 lb in

DOOR LOCKS
Front Side Door Lock Cylinder Clamp Screw 5 N.m 44 lb in
Front Side Door Latch Screws 10 N.m 89 lb in
Front Side Door Interlock Striker Bolt 10 N.m 89 lb in
Front Side Door Outside Handle Screw 10 N.m 89 lb in
Front Side Door Latch Striker Screws 25 N.m 18 lb ft
Front Side Door Interlock Striker Plate Screws 10 N.m 89 lb in
Rear Compartment Lid Latch Bolts 10 N.m 89 lb in
Rear Compartment Lid Latch Striker Bolts 10 N.m 89 lb in

DRIVESHAFT
Propeller Shaft Center Bearing Mounting Bolt 22 N.m 16 lb ft
Propeller Shaft Coupling Nut- Front 91 N.m 67 lb ft
Propeller Shaft Coupling Nut- Rear 91 N.m 67 lb ft
Propeller Shaft to Rear Differential Drive Flange Bolt 115 N.m 85 lb ft
Propeller Shaft to Transmission Output Flange Nut 97 N.m 72 lb ft

ENGINE COOLING
Air Conditioning (A/C) Condenser Bolt 6.5 N.m 58 lb in
Air Conditioning (A/C) Line Clip to Fan Shroud Screw 1 N.m 9 lb in
Auxiliary Cooling Fan Bolt 6.5 N.m 58 lb in
Brake Master Cylinder Nut 25 N.m 18 lb ft
Clutch Master Cylinder Bolt 50 N.m 37 lb ft
Coolant Air Bleed Pipe Cover Bolt (LSA) 12 N.m 106 lb in
Coolant Air Bleed Stud (LSA) 12 N.m 106 lb in
Coolant Pipe to Cylinder Head Bolt (LLT) 50 N.m 37 lb ft
Coolant Pipe to Generator Bracket Bolt (LLT) 10 N.m 89 lb in
Coolant Pipe to Thermostat Housing Bolt (LLT) 10 N.m 89 lb in
Electric Cooling Fan Blade Nut 7 N.m 62 lb ft
Coolant Recovery Reservior Bolt 17 N.m 13 lb in
Electric Cooling Fan Motor Screw 5 N.m 44 lb in
Electric Cooling Fan Resistor Bolt 5.4 N.m 48 lb in
Electric Cooling Fan Shroud to Plenum Bolt 6.5 N.m 58 lb in
Electric Cooling Fan Shroud to Radiator Bolt 6.5 N.m 58 lb in
Engine Coolant Heater (LSA) 50 N.m 37 lb ft
Engine Coolant Heater Cord Fastener (LSA) 10 N.m 89 lb in
Engine Coolant Heater Ground Wire Bolt (LLT) 12 N.m 106 lb in
Oil Level Indicator Tube Bolt 20 N.m 15 lb ft
Radiator Support Bracket Bolt 9 N.m 80 lb in
Thermostat Bolt (LLT) 10 N.m 89 lb in
Thermostat Housing Bolt (LLT) 20 N.m 15 lb ft
Thermostat Housing Bolt (LSA) 15 N.m 11 lb ft
Water Outlet Housing Bolt (LLT) 10 N.m 89 lb in
Water Pump Bolt (LLT) 10 N.m 89 lb in
Water Pump Bolt (LSA) 30 N.m 22 lb ft
Water Pump Pulley Bolt (LLT) 12 N.m 106 lb in

ENGINE ELECTRICAL
Battery Hold Down Retainer Bolt 22 N.m 16 lb ft
Battery Negative Cable Bolt (at rear compartment floor) 25 N.m 18 lb ft
Battery Negative Cable Terminal Nut 15 N.m 11 lb ft
Battery Positive Cable Nut (at the fuse block) 15 N.m 11 lb ft
Battery Positive Cable Nut (at the junction block) 15 N.m 11 lb ft
Battery Positive Cable Nut (at the starter) 13 N.m 115 lb in
Battery Positive Cable Terminal Nut 5 N.m 44 lb in
Engine Harness and Battery Positive Cable Harness
Retainers 12 N.m 9 lb ft
Generator BAT Terminal Nut 15 N.m 11 lb ft
Generator Bolt 58 N.m 43 lb ft
Generator Bracket Bolt (at the front of the bracket) 50 N.m 37 lb ft
Generator Bracket Nut (at the front of the bracket) 50 N.m 37 lb ft
Starter 58 N.m 43 lb ft
Starter Motor Mounting Bolt 58 N.m 43 lb ft
Starter Shield Bolt 5 N.m 44 lb in

ENTERTAINMENT & NAVIGATION
Communication Interface Module Bracket Bolt Screw 10 N.m 89 lb in
Front Floor Console Bolts 2.5 N.m 22 lb in
Front Overhead Console Bolt Screw 2 N.m 18 lb in
Radio Antenna Module Bolt 9 N.m 80 lb in
Radio Antenna Module Coil Bolt 10 N.m 89 lb in
Radio Control Assembly Bolt Screw 2.5 N.m 22 lb in
Radio Front Side Door Speaker Bolt/Screw 2.5 N.m 22 lb in
Radio Front Side Door Upper Speaker Grille Bolt 2 N.m 18 lb in
Radio Front Speaker Bolt/Screw 2.5 N.m 22 lb in
Radio Rear Speaker Bolt Screw 2.5 N.m 22 lb in
Radio Screw 2.5 N.m 22 lb in
Radio Speaker Amplifier Nut 9 N.m 80 lb in

EXTERIOR TRIM
Front Wheelhouse Liner Screw 3 N.m 27 lb in
Rear Wheelhouse Liner Screw 3 N.m 27 lb in
Rear End Spoiler Nut 6 N.m 53 lb in

 

[CamaroPA]

FRONT SUSPENSION
Front Lower Control Arm Adjuster Nut 50 N.m 37 lb ft +150°
Front Lower Front Control Arm Nut at the Steering Knuckle 40 N.m 30 lb ft +90°
Front Lower Rear Control Arm Nut at the Steering Knuckle 40 N.m 30 lb ft +90°
Front Lower Rear Control Arm Bolt at the Frame 50 N.m 37 lb ft +120°
Front Stabilizer Shaft Link Nut at the Front Strut 50 N.m 36 lb ft
Front Stabilizer Shaft Link Nut at the Stabilizer Shaft 50 N.m 36 lb ft
Front Stabilizer Shaft Insulator Clamp Nuts 17 N.m 13 lb ft
Front Suspension Strut Bolts at the Steering Knuckle 80 N.m 59 lb ft +180°
Front Suspension Strut Nut at the Front Suspension Strut Mounting Plate 70 N.m 52 lb ft
Front Suspension Strut Nut at the Front Suspension Strut Insulator 70 N.m 52 lb ft
Front Wheel Bearing/Hub Bolts 108 N.m 79 lb ft

REAR SUSPENSION
Adjustable Link Adjuster Nut 115 N.m 85 lb ft
Lower Control Arm Adjuster Nut 115 N.m 85 lb ft
Lower Control Arm to Knuckle Bolt, First Pass 40 N.m 30 lb ft, Final Pass + 120°
Lower Rear Shock Absorber Nut, First Pass 80 N.m 59 lb ft, Final Pass + 120°
Rear Shock Absorber Nut 45 N.m 33 lb ft
Rear Stabilizer Shaft Insulator Clamp Bolts 22 N.m 16 lb in
Rear Stabilizer Shaft Link Nuts 49 N.m 36 lb ft
Rear Wheel Bearing and Hub Bolts 115 N.m 85 lb ft
Rear Wheel Drive Shaft Nut (New) 270 N.m 199 lb ft
Trailing Arm to Frame Bolt 100 N.m 74 lb ft
Trailing Arm to Knuckle Bolts, First Pass 40 N.m 30 lb ft, Final Pass + 120°
Upper Control Arm to Bushing Bolt 160 N.m 118 lb ft
Upper Control Arm to Knuckle Bolts, First Pass 60 N.m 44 lb ft, Final Pass + 90°
Upper Control Arm to Frame Bolt, First Pass 80 N.m 59 lb ft, Final Pass + 120°
Upper Control Arm to Bushing to Frame Bolt, First Pass 50 N.m 37 lb ft, Final Pass + 120°
Upper Rear Shock Absorber Bolt 58 N.m 43 lb ft

POWER STEERING
Power Steering Fluid Cooler Hose Bracket Bolt 9 N.m 80 lb in
Power Steering Fluid Reservoir Bracket Bolt, V6 9 N.m 80 lb in
Power Steering Gear Inlet Hose Bracket Bolts 9 N.m 80 lb in
Power Steering Gear Inlet Hose Fitting 34 N.m 25 lb ft
Power Steering Gear Outlet Hose Bracket Bolts 9 N.m 80 lb in
Power Steering Gear Outlet Hose Fitting 34 N.m 25 lb ft
Power Steering Pump Auxiliary Bracket Bolt, V6 20 N.m 15 lb ft
Power Steering Pump Bracket Bolt, V6 58 N.m 43 lb ft
Power Steering Pump Bracket Bolt, V8 50 N.m 37 lb ft
Power Steering Pump Bolt, V6 22 N.m 16 lb ft
Power Steering Pump Bolt, V8 25 N.m 18 lb ft
Steering Gear Bolts, First Pass 50 N.m 37 lb ft, Second Pass 120°
Steering Gear Pinion Bolt 50 N.m 37 lb ft
Steering Linkage Inner Tie Rod 75 N.m 55 lb ft
Steering Linkage Inner Tie Rod Nut 75 N.m 55 lb ft
Steering Linkage Inner Tie Rod Thread Locking Adhesive Loctite® 271 89021297 10953488
Steering Linkage Outer Tie Rod Nut, First Pass 30 N.m 22 lb ft, Second Pass 120°

 

[CamaroPA]

ENGINE

A/C
 Compressor Bolt - Rear - CTS Only 45 N.m 33 lb ft
 Compressor Bolt - Rear - All Except CTS 58 N.m 43 lb ft
 Compressor Bolt - Front 22 N.m 17 lb ft
 Compressor Bracket Bolt - Front 50 N.m 37 lb ft
 Compressor Hose Assembly Bolt 9 N.m 80 lb in
Camshaft Cap Bolt 10 N.m 89 lb in
Camshaft Cover Bolt 10 N.m 89 lb in
Camshaft Intermediate Drive Sprocket Bolt - Idler Sprocket 58 N.m 43 lb ft
Camshaft Position Actuator
 Camshaft Bolt 58 N.m 43 lb ft
 Oil Control Valve Bolt 10 N.m 89 lb in
Camshaft Position Sensor Bolt 10 N.m 89 lb in
Catalytic Converter
 Exhaust Manifold Nut 50 N.m 37 lb ft
Close Out Cover Bolt 10 N.m 89 lb in
Clutch Pressure Plate Bolts 30 N.m 22 lb ft
Connecting Rod Bolt
 First Pass 30 N.m 22 lb ft
 Second Pass - Counterclockwise Back Off to Zero
 Third Pass 25 N.m 18 lb ft
 Final Pass 110 Degrees
Coolant Outlet Bolt 10 N.m 89 lb in
Crankshaft Balancer Bolt
 First Pass 100 N.m 74 lb ft
 Final Pass 150 Degrees
Crankshaft Main Bearing Bolt - Inner
 First Pass 20 N.m 15 lb ft
 Final Pass 80 degrees
Crankshaft Main Bearing Bolt - Outer
 First Pass 15 N.m 11 lb ft
 Final Pass 110 Degrees
Crankshaft Main Bearing Bolt - Side
 First Pass 30 N.m 22 lb ft
 Final Pass 60 Degrees
Crankshaft Position Sensor Bolt 10 N.m 89 lb in
Crankshaft Rear Oil Seal Housing Bolt 10 N.m 89 lb in
Cylinder Head Bolt - M8
 First Pass 15 N.m 11 lb ft
 Final Pass 75 Degrees
Cylinder Head Bolt - M11
 First Pass 30 N.m 22 lb ft
 Final Pass 150 degrees
Cylinder Head Core Hole Plug 31 N.m 23 lb ft
Drive Belt
 Idler Pulley Bolt 58 N.m 43 lb ft
 Tensioner Bolt 58 N.m 43 lb ft
ECM
 Bolt 10 N.m 89 lb in
 Bracket Bolt - Front 23 N.m 17 lb ft
 Bracket Bolt - Side 10 N.m 89 lb in
 Grounding Bolt 4.5 N.m 40 lb in
ECT Sensor 30 N.m 22 lb ft
Engine Flex Plate, Auto Trans, Bolt
 First Pass 30 N.m 22 lb ft
 Final Pass 45 Degrees
Engine Flywheel, Manual Trans, Bolt 67 N.m 49 lb ft
Engine Front Cover Studs 15 N.m 11 lb ft
Engine Front Cover Bolt - M6 15 N.m 11 lb ft
Engine Front Cover Bolt - M8
 First Pass 20 N.m 14 lb ft
 Second Pass 20 N.m 14 lb ft
 Final Pass 60 Degrees
Engine Front Cover Bolt - M12 65 N.m 48 lb ft
Engine Mount
 Bracket Bolt to Engine Block - M8 (AWD) 38 N.m 28 lb ft
 Bracket Bolt to Engine Block - M8 (RWD) 22 N.m 16 lb ft
 Bracket Bolt to Engine Block - M10 60 N.m 45 lb ft
 Nut to Engine Mount Bracket 80 N.m 59 lb ft
 Nut to Frame 80 N.m 59 lb ft
Engine Wiring Harness Bracket
 Bolt - Cylinder Head Rear 40 N.m 30 lb ft
 Bolt - ECM Bracket Side 23 N.m 17 lb ft
 Bolt - ECM Bracket Top 10 N.m 89 lb in
 Bolt - Left Side Oil Filter Adapter 10 N.m 89 lb in
 Bolt - Left Side Oil Pan 10 N.m 89 lb in
 Bolt - Near Crankshaft Position Sensor 50 N.m 37 lb ft
 Bolt - Right Side Block Front 23 N.m 17 lb ft
 Bolt - Right Side Head Front 10 N.m 89 lb in
Engine Wiring Harness Ground
 Bolt - ECM Bracket Top 10 N.m 89 lb in
 Bolt - Left Cylinder Head Side 10 N.m 89 lb in
 Bolt - Right Cylinder Head Rear 10 N.m 89 lb in
EVAP Purge Valve Bolt 10 N.m 89 lb in
Exhaust Manifold
 Bolt 20 N.m 15 lb ft
 Heat Shield Bolt 10 N.m 89 lb in
 Lower Heat Shield, Knock Sensor Shield, Bolt 58 N.m 43 lb ft
Fuel Injection Fuel Rail Fuel Pressure Sensor 33 N.m 25 lb ft
Fuel Line Pressure Fuel Line Fitting Nuts 30 N.m 22 lb ft
Fuel Pump Bolts - High Pressure 15 N.m 11 lb ft
Fuel Rail Bolt 10 N.m 89 lb in
Generator
 Bolt 50 N.m 37 lb ft
 Bracket Bolt - Front 50 N.m 37 lb ft
 Bracket Bolt - Side 22 N.m 16 lb ft
 Cable Nut 13 N.m 115 lb in
Ground Cable Bolt 50 N.m 37 lb ft
Heater Inlet/Outlet Pipe Assembly Bolt 10 N.m 89 lb in
Ignition Coil Bolt 10 N.m 89 lb in
Intake Manifold
 Brace Bolt - Engine Front Cover M12 65 N.m 48 lb ft
 Brace Bolt/Ball Stud - Intake Manifold M6 10 N.m 89 lb in
 Ball Stud to Cam Cover M6 5 N.m 44 lb in
 Sight Shield Ball Stud 10 N.m 89 lb in
 Tuning Valve Bolt 10 N.m 89 lb in
 Upper-to-Cylinder Head Bolt - Long 25 N.m 18 lb ft
 Upper-to-Cylinder Head Bolt - Short 25 N.m 18 lb ft
 Upper-to-Lower Intake Manifold Bolt 25 N.m 18 lb ft
Knock Sensor Bolt 25 N.m 18 lb ft
MAP Sensor Bolt 10 N.m 89 lb in
Oil Drain Plug 25 N.m 18 lb ft
Oil Filter Cap 25 N.m 18 lb ft
Oil Filter Housing Adapter
 Bolt - Cylinder Head M10 58 N.m 43 lb ft
 Bolt - Engine Block M8 25 N.m 18 lb ft
Oil Gallery Plug 31 N.m 23 lb ft
Oil Level Indicator Tube Bolt 10 N.m 89 lb in
Oil Pan
 Bolt - Block M8 25 N.m 18 lb ft
 Bolt - Crankshaft Rear Oil Seal Housing M6 10 N.m 89 lb in
 Windage Tray Bolt 10 N.m 89 lb in
Oil Pressure Sender 20 N.m 15 lb ft
Oil Pump
 Bolt 25 N.m 18 lb ft
 Cover Bolt 13 N.m 115 lb in
Oxygen Sensor
 Pump Converter Pipe 40 N.m 30 lb ft
PCV Tube Bracket Bolt 10 N.m 89 lb in
Piston Oil Cooling Nozzle Bolt 10 N.m 89 lb in
Power Steering Pump Bracket to Engine Bolt
 Acadia/Enclave/Outlook/Traverse; Equinox/Terrain; Vue 50 N.m 37 lb ft
 All Except: Acadia/Enclave/Outlook/Traverse; Equinox/Terrain; Vue 58 N.m 43 lb ft
 Pump to Bracket Bolt 22 N.m 16 lb ft
 Reservoir Bolt - Lower 25 N.m 18 lb ft
 Reservoir Bolt - Upper 9 N.m 80 lb in
Primary Camshaft Drive Chain
 Left Lower Guide Bolt - Oil Pump - Second Design 25 N.m 18 lb ft
 Tensioner Bolt 25 N.m 18 lb ft
 Upper Guide Bolt 25 N.m 18 lb ft
Radiator Outlet Pipe
 Bolt - Generator Bracket 25 N.m 18 lb ft
 Bolt - Right Cylinder Head Rear 58 N.m 43 lb ft
 Bolt - Thermostat Housing 25 N.m 18 lb ft
Secondary Camshaft Drive Chain
 Guide Bolt 25 N.m 18 lb ft
 Shoe Bolt 25 N.m 18 lb ft
 Tensioner Bolt 25 N.m 18 lb ft
Spark Plug 18 N.m 13 lb ft
Starter Motor
 Bolt 58 N.m 43 lb ft
 Cable Nut 13 N.m 115 lb in
Suction Tube Bolt 10 N.m 89 lb in
Suction Screen Bolt 10 N.m 89 lb in
Thermostat Housing Bolt 10 N.m 89 lb in
Throttle Body Bolt 10 N.m 89 lb in
Torque Converter Bolt 60 N.m 44 lb ft
Transmission
 Mount Bolt to Transmission - RPO M82 60 N.m 45 lb ft
 Range Selector Lever Nut 9.5 N.m 84 lb in
 To Engine Bolt 50 N.m 37 lb ft
Water Pump
 Bolt 10 N.m 89 lb in
 Pulley Bolt 10 N.m 89 lb in

 

[CamaroPA]

LLT ENGINE MECHANICAL SPECIFICATIONS
General
 Engine Type V-6
 Displacement 3.6 Liter 217 cu in
 RPO LLT
 VIN V-cars/D-trucks
 Bore 94 mm 3.7008 in
 Stroke 85.6 mm 3.37 in
 Compression Ratio 11.4:1
 Firing Order 1-2-3-4-5-6
 Spark Plug Gap 1.1 mm 0.0433 in
Block
 Crankshaft Main Bearing Bore Diameter 72.867-72.881 mm 2.8688-2.8693 in
 Cylinder Bore Diameter 93.992-94.008 mm 3.7005-3.7011 in
 Cylinder Bore Out-of-Round - Production Max. 0.013 mm 0.0005 in
Camshaft
 Camshaft Bearing Inside Diameter - Front Number 1 35.000-35.020 mm 1.3779-1.3787 in
 Camshaft Bearing Inside Diameter - Middle and Rear Number 2-4 27.000-27.020 mm 1.0630-1.0638 in
 Camshaft End Play 0.045-0.215 mm 0.0018-0.0085 in
 Camshaft Journal Diameter - Front Number 1 34.936-34.960 mm 1.3754-1.3764 in
 Camshaft Journal Diameter - Middle and Rear Number 2-4 26.936-26.960 mm 1.0605-1.0614 in
 Camshaft Journal Out-of-Round 0.006 mm 0.0002 in
 Camshaft Journal to Bore Clearance 0.040-0.084 mm 0.0016-0.0033 in
 Camshaft Lobe Lift - Exhaust 42.425-42.725 mm 1.6703-1.6821 in
 Camshaft Lobe Lift - Intake 42.385-42.685 mm 1.6687-1.6805 in
 Camshaft Runout - Front and Rear Number 1 and 4 0.025 mm 0.0010 in
 Camshaft Runout - Middle 2 and 3 0.050 mm 0.0020 in
 Valve Lift - Exhaust 10.8 mm 0.4252 in
 Valve Lift - Intake 10.8 mm 0.4252 in
Connecting Rod
 Connecting Rod Bearing Clearance 0.010-0.070 mm 0.0004-0.0028 in 59.620-59.636 mm 2.3472-2.3479 in
 Connecting Rod Bore Diameter - Bearing End
 Connecting Rod Bore Diameter - Pin End - Production 24.009-24.019 mm 0.9452-0.9456 in
 Connecting Rod Bore Diameter - Pin End - Service Maximum 24.021 mm 0.9457 in
 Connecting Rod Length - Center to Center 152.400 mm 6.0000 in
 Connecting Rod Side Clearance 0.095-0.355 mm 0.0374-0.0140 in
 Connecting Rod Width - Bearing End
 Production 21.775 mm 0.8573 in
 Service 21.725-21.825 mm 0.8553-0.8593 in
 Connecting Rod Width - Pin End
 Production 21.775 mm 0.8573 in
 Service 21.725-21.825 mm 0.8553-0.8593 in
Crankshaft
 Connecting Rod Journal Diameter 55.992-56.008 mm 2.2044-2.2050 in
 Connecting Rod Journal Out-of-Round 0.005 mm 0.0002 in
 Connecting Rod Journal Taper 0.005 mm 0.0002 in
 Connecting Rod Journal Width
 Production 22.000 mm 0.8661 in
 Service 21.920-22.080 mm 0.8630-0.8693 in
 Crankshaft End Play 0.100-0.330 mm 0.0039-0.0130 in
 Crankshaft Main Bearing Clearance 0.010-0.060 mm 0.0004-0.0024 in
 Crankshaft Main Journal Diameter 67.992-68.008 mm 2.6768-2.6775 in
 Crankshaft Main Journal Out-of-Round 0.005 mm 0.0002 in
 Crankshaft Main Journal Taper 0.005 mm 0.0002 in
 Crankshaft Main Journal Thrust Wall
 Runout 0.000-0.040 mm 0.0000-0.0016 in
 Square 0.000-0.010 mm 0.0000-0.0004 in
 Crankshaft Main Journal Width, #2, 4
 Production 24.000 mm 0.9449 in
 Service 23.900-24.100 mm 0.9409-0.9488 in
 Crankshaft Main Journal Width, #3
 Production 24.400 mm 0.9606 in
 Service 24.360-24.440 mm 0.9591-0.9622 in
 Crankshaft Pilot Bearing Bore Diameter 20.965-20.995 mm 0.8254-0.8266 in
 Crankshaft Rear Flange Runout 0.025 mm 0.0010 in
 Crankshaft Reluctor Ring Runout - Maximum 1.500 mm 0.0591 in
 Crankshaft Runout 0.030 mm 0.0012 in
 Crankshaft Thrust Bearing Clearance 0.076-0.305 mm 0.0030-0.0120 in
 Crankshaft Thrust Surface - Height Diameter 95.000 mm 3.7401 in
 Crankshaft Thrust Surface Runout 0.040 mm 0.0016 in
Cylinder Head
 Valve Guide Bore - Exhaust 6.000-6.020 mm 0.2362-0.2370 in
 Valve Guide Bore - Intake 6.000-6.020 mm 0.2362-0.2370 in
 Valve Guide Installed Height 14.050-14.550 mm 0.5531-0.5728 in
 Valve Lifter Bore Diameter 12.008-12.030 mm 0.4728-0.4736 in
Lubrication System
 Oil Capacity - with Filter 5.68 Liters 6 Quarts
 Oil Capacity - without Filter 5.20 Liters 5.5 Quarts
 Oil Pressure - Minimum @ Idle 69 kPa 10 psi
 Oil Pressure - Minimum @ 2,000 RPM 138 kPa 20 psi
 Piston Cooling Jet Valve Opening Pressure 1.7-2.3 bar 25-33 psi
Piston Rings
 Piston Ring End Gap
 First Compression Ring - Nominal 0.150-0.300 mm 0.0059-0.0118 in
 First Compression Ring - Maximum, Ring in Bore 0.390 mm 0.1535 in
 Second Compression Ring - Nominal 0.280-0.480 mm 0.0110-0.0189 in
 Second Compression Ring - Maximum, Ring in Bore 0.560 mm 0.0220 in
 Oil Control Ring 0.150-0.600 mm 0.0059-0.0236 in
 Piston Ring to Groove Clearance
 First Compression Ring 0.030-0.065 mm 0.0012-0.0026 in
 Second Compression Ring 0.015-0.060 mm 0.0006-0.0024 in
 Oil Control Ring 0.030-0.170 mm 0.0012-0.0067 in
 Piston Ring Thickness
 First Compression Ring 1.175-1.190 mm 0.0463-0.0469 in
 Second Compression Ring 1.470-1.495 mm 0.0579-0.0589 in
 Oil Control Ring 2.360-2.480 mm 0.0929-0.0976 in
Pistons and Pins
 Piston
 Piston Diameter - Measured Over Skirt Coating 93.976-94.014 mm 3.6998-3.7013 in
 Piston Diameter - Service Limit Minimum w/more than 10K miles 93.926 mm 3.6979 in
 Piston Pin Bore Diameter 24.004-24.009 mm 0.9450-0.9452 in
 Piston Ring Groove Width - First Compression Ring 1.220-1.240 mm 0.0480-0.0488 in
 Piston Ring Groove Width - Second Compression Ring 1.510-1.530 mm 0.0595-0.0602 in
 Piston Ring Groove Width - Oil Control Ring 2.510-2.530 mm 0.0988-0.0996 in
 Piston to Bore Clearance - Production; Measured at Skirt Coating 0.022-0.032 mm 0.0008-0.0013 in
 Piston to Bore Clearance - Service Limit Maximum, w/more than 10k miles
 Pin
 Piston Pin Clearance to Connecting Rod Bore - Production 0.007-0.024 mm 0.0003-0.0010 in
 Piston Pin Clearance to Connecting Rod Bore - Service Maximum 0.030 mm 0.0012 in
 Piston Pin Clearance to Piston Pin Bore - Production 0.004-0.012 mm 0.0002-0.0005 in
 Piston Pin Clearance to Piston Pin Bore - Service Maximum 0.015 mm 0.0006 in
 Piston Pin Diameter 23.997-24.000 mm 0.9448-0.9449 in
 Piston Pin Length 60.600-61.100 mm 2.3858-2.4055 in
Valve System
 Valves
 Valve Face Angle 44.25 degrees
 Valve Face Runout 0.038 mm 0.0015 in
 Valve Face Width - Exhaust 2.750 mm 0.1083 in
 Valve Face Width - Intake 2.180 mm 0.0858 in
 Valve Head Diameter - Exhaust 30.470-30.730 mm 1.1996-1.2098 in
 Valve Head Diameter - Intake 36.830-37.090 mm 1.4500-1.4602 in
 Valve Installed Height 35.23-36.69 mm 1.3870-1.4445 in
 Valve Length - Exhaust 97.110 mm 3.8232 in
 Valve Length - Intake 101.230 mm 3.9854 in
 Valve Seat Angle - Seating Surface 45 degrees
 Valve Seat Angle - Relief Surface 30 degrees
 Valve Seat Angle - Undercut Surface 60 degrees
 Valve Seat Roundness- Maximum 0.025 mm 0.0010 in
 Valve Seat Runout - Maximum 0.080 mm 0.0032 in
 Valve Seat Width - Exhaust Seating Surface 1.400-1.800 mm 0.0551-0.0709 in
 Valve Seat Width - Exhaust Relief Surface 0.700-0.900 mm 0.0276-0.0354 in
 Valve Seat Width - Intake Seating Surface 1.000-1.400 mm 0.0394-0.0551 in
 Valve Seat Width - Intake Relief Surface 0.500-0.700 mm 0.0197-0.0276 in
 Valve Stem Diameter - Exhaust 5.945-5.965 mm 0.2341-0.2348 in
 Valve Stem Diameter - Intake 5.955-5.975 mm 0.2344-0.2352 in
 Valve Stem-to-Guide Clearance - Exhaust 0.035-0.075 mm 0.0014-0.0030 in
 Valve Stem-to-Guide Clearance - Intake 0.025-0.065 mm 0.0010-0.0026 in
 Valve Lifters - Stationary Hydraulic Lash Adjuster (SHLA)
 Valve Lifter (SHLA) Diameter 11.989-12.000 mm 0.4720-0.4724 in
 Valve Lifter (SHLA)-to-Bore Clearance 0.008-0.041 mm 0.0003-0.0016 in
 Rocker Arms
 Valve Rocker Arm Ratio 1.68 to 1
 Valve Rocker Arm Roller Diameter 17.750-17.800 mm 0.6988-0.7008 in
 Valve Springs
 Valve Spring Coil Thickness 3.250 x 3.900 mm 0.1280 x 0.1535 in
 Valve Spring Diameter - Inside Top 12.200-12.700 mm 0.4803-0.4999 in
 Valve Spring Diameter - Outside Top 20.250 mm 0.7972 in
 Valve Spring Diameter - Inside Bottom 17.950-18.450 mm 0.7067-0.7264 in
 Valve Spring Diameter - Outside Bottom 26.000 mm 1.0236 in
 Valve Spring Free Length 42.500-45.500 mm 1.6732-1.7913 in
 Valve Spring Installed Height - Closed 35.000 mm 1.3779 in
 Valve Spring Installed Height - Open 24.000 mm 0.9449 in
 Valve Spring Load - Closed 247-273 N 56-61 lb
 Valve Spring Load - Open 598-662 N 134-149 lb

 

[CamaroPA]

ADHESIVES, FLUIDS, LUBRICANTS, AND SEALERS

Block Pan Rail Sealant US PART# 12378521 CANADIAN PART# 88901148
Camshaft Prelube Lubricant 88862586 88862827
Coolant Drain Threaded Plug Sealant 12346004 10953480
Coolant Expansion Plugs Sealant 12378521 88901148
Coolant and Oil Plug Threads Sealant 12346004 10953480
Crankshaft Bearing Surfaces - Upper/Lower Lubricant 1052367 992869
Lubricant 12345501 992704
Crankshaft Connecting Rod Bearing Journal Lubricant 1052367 992869
Lubricant 12345501 992704
Crankshaft Prelube Lubricant 1052367 992869
Crankshaft Rear Oil Seal Housing Sealant 12378521 88901148
Engine Front Cover/Split Lines Sealant 12378521 88901148
Engine Oil 5W-30 Mineral Oil 12345610 00799389
Fuel Injection Fuel Rail Fuel Pressure Sensor
Sealing Cone/Threads Lubricant 12345610 993193
Fuel Rail Sealing Cone/Threads Lubricant 12345610 993193
GM Fuel System Treatment Plus Cleaner 88861011 -
Oil Gallery Threaded Plug Sealant 12346004 10953480
Oil Pan, Engine Front Cover, Crankshaft Rear Sealant 12378521 (150g cartridge) 88901148
Oil Seal Housing, Expansion Plugs Sealant 88861417 (75gram squeeze tube) 88861418
Piston Pin Bores Lubricant 1052367 992869
Positive Crankcase Ventilation (PCV) Orifice Sealant 12378521 88901148
Stationary Hydraulic Lash Adjuster (SHLA) Engine Oil 12345610 993193
SHLA Bores in Cylinder Head Engine Oil 12345610 993193
SHLA Pivot Spheres Lubricant 12345501 992704
Valve Stem/Guide ID Lubricant 12345501 992704

Thread Repair
-Cutting Fluid 1052864 992881
-Cleaner 12346139 or 12377981 10953463
-Sealant 12345493 10953488